• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they are not susceptible to rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. It is important to take the time to ensure that you're doing everything you can to ensure that your windows are in good repair.

Single-pane windows are relatively simple to replace, and they will usually fit into the frames of the past easily. However If you have double pane windows that are secured by internal beading, it will be more difficult to get rid of the existing panes and install new ones. In this case you'll need source some plastic spacers to aid the new pane in being able to fit properly into the frame of the window.

Wearing eye protection and thick gloves is a must if you plan to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes so that any shards of glass fall onto the fabric, not onto the floor which could cause them to be trampled.

Once the glass is removed from the window, it's best to cover the gap with clear packaging tape or duct tape to stop water and drafts from getting into the home until a professional comes out and fix the window. It also acts as a barrier, preventing any intruders to gain access to your home. If the gap between the window and the door is significant, you may prefer a security screen that also includes a window. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows made of sash. In time, they could develop a variety of issues such as sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from becoming worse.

Repositioning the hinges could aid in fixing a window which is sagging. You'll first need to open the windows to get at the frame. Then, using an screwdriver, unscrew the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you've moved your hinges. If you're satisfied with the fit, tighten the screws until they stay in the right place.

If you cannot reposition the hinges, you could need to replace the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to lose tightness. It is important to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

upvc Window repair handles may also become loose. Often it is due to screws that have become loose over time. However, it could occur because the handle mechanism has been worn out. It's relatively simple to fix a loose uPVC hand. First, you'll need to close the window and then perform an initial test fit. The corner joints of the sash should align with the casing joint. If it isn't then you can use a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

If you wake up to damp floors and mouldy walls each time it rains, it is important that you take action. Windows that leak water do are not just a cause for degrading of the structure of your home but also hamper your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any skilled DIYer. Depending on how severe the issue is, the old caulking may need to be removed. It is essential to remember that when it comes to uPVC window repairs you should not be tempted to 'over-caulk' as this will only make the area more difficult to clean and can reduce the efficiency of your energy.

Check that any drainage holes have no debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious instances, you might have to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

It is also important to keep in mind that if the leakage is coming from between the glass in your double glazed window repairs near me glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open in a breeze it could be the hinges that are at the fault. They can be replaced by any competent DIYer and can usually be done within a few minutes.

Like all mechanical parts hinges will wear out over time. It's very simple to change the hinges on a window but it's much simpler if you have someone to help you hold the frame.

Check that the uPVC hinges are open and closed in the correct direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The issue could be caused either by opening the window improperly or a faulty installation in the factory. Sending us photos via our website is often enough to solve the issue. We are more than happy to offer advice.

Regular lubrication of hinges is also essential. Applying a light engineering lubricant on the hinges is a great way to do this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It also decreases the risk of a window getting stuck and stop corrosion. This must be done at a minimum every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by different factors. The hinges can also become misaligned due to wear, creating a gap where the sash meets frame. This can be easily repaired by giving them thorough clean, however in the event that they are beyond repair it may be necessary to get them realigned or replaced. The interlock, which is located on the hinge of the window, may also be misaligned, and again it may be feasible to give them a clean but in some instances it could be necessary to have these replaced.

The seals may wear out or become damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. which will help regulate indoor temperatures and will lessen the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler which can be put on top of your window sill. They can help stop cold air from entering and keep your home warm and cozy!

With a little maintenance and repairs your windows made of upvc will provide an excellent level of insulation and security for your home. It is essential to remember that all windows will eventually wear out and it may be more cost-effective to simply replace them instead of fixing them. If you have any problems with your window made of upvc you should consult an expert immediately.